Hyundai Creta: Tires/Wheels / Alignment: Repair procedures

Hyundai Creta GS 2014-2024 Service Manual / Suspension System / Tires/Wheels / Alignment: Repair procedures

Front Wheel Alignment

•	When using a commercially available computerized wheel alignment equipment to inspect the front wheel alignment, always position the vehicle on a level surface with the front wheels facing straight ahead.

•	Prior to inspection, make sure that the front suspension and steering system are in normal operating condition and that the tires are inflated to the specified pressure.

Toe

B - A > 0: Toe in

B - A < 0: Toe out

Toe Adjustment

1.	Loosen the tie rod end lock nut.

2.	Remove the bellows clip to prevent the bellows from being twisted.

Adjust the toe by screwing or unscrewing the tie rod. Toe adjustment should be made by turning the right and left tie rods by the same amount.

Toe

Total : 0.1°±0.2°

Individual : 0.05°±0.1°

When completing the toe adjustment, install the bellows clip and tighten the tie rod end lock nut to specified torque.

Tightening torque :

49.0 ~ 53 N.m (5.0 ~ 5.5 kgf.m, 36.2 ~ 39.8 lb-ft)

Camber

Camber : -0.5°±0.5°

When the wheel tilts out at the top, then the camber is positive (+).

When the wheel tilts in at the top, then the camber is negative (-).

Camber and Caster are pre-set at the factory, so they do not need to be adjusted. If the camber and caster are not within the standard value, replace or repair the damaged parts and then inspect again.

Item	Description
A	Positive camber angle
B	True vertical
C	Strut centerline

Caster

Caster is the tilting of the strut axis either forward or backward from vertical. A backward tilt is positive (+) and a forward tilt is negative (-).

Caster is pre-set at the factory and doesn't need to be adjusted. If the caster is not within the standard value, replace the bent or damaged parts.

Caster : 4.28°±0.5°

King-pin angle

King-pin : 13.21°±0.5°

•	The worn loose or damaged parts of the front suspension assembly must be replaced prior to measuring front wheel alignment.

•	Caster are pre-set to the specified value at the factory and don't need to be adjusted.

•	If the caster are not within specifications, replace bent or damaged parts.

•	The difference of left and right wheels about the the caster must be within the range of 0° ± 0.5°.

Rear Wheel Alignment

•	When using a commercially available computerized wheel alignment equipment to inspect the rear wheel alignment, always position the vehicle on a level surface.

•	Prior to inspection, make sure that the rear suspension system is in normal operating condition and that the tires are inflated to the specified pressure.

Toe

B - A > 0: Toe in (+)

B - A < 0: Toe out (-)

Toe is pre-set at the factory, so it does not need to be adjusted. If the toe is not within the standard value, replace or repair the damaged parts and then inspect again.

Toe

Total : 0.3°±0.2°

Individual : 0.15°±0.1°

Camber

Camber is pre-set at the factory, so it does not need to be adjusted. If the camber is not within the standard value, replace or repair the damaged parts and then inspect again.

Camber angle : -1.5°±0.5° 39

Wheel: Repair procedures

Inspection Hub nut tightening sequence Tighten the hub nuts as follows. Tightening torque (Front) : 88.25 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft ...

Steering System

...

Other information:

Hyundai Creta GS 2014-2024 Service Manual: Torque Converter Control Solenoid Valve (T/CON_VFS)
Description and operation Description • Torque converter control solenoid valve (T/CON_VFS) is attached to the valve body. • This variable force solenoid valve indirectly controls the hydraulic pressure inside the torque ...

Hyundai Creta GS 2014-2024 Owners Manual: Electric power steering (EPS)
The system assists you with steering the vehicle. If the engine is off or if the power steering system becomes inoperative, the vehicle may still be steered, but it will require increased steering effort. Also, the steering effort becomes heavier as the vehicle’s speed increases and ...